#Electrical wire splice zip
#Electrical wire splice free

You can then trim off the excess of the zip tie end with a pair of scissors if using this method. Wrap the zip tie or use electrical tape around the bottom of the stripped insulation jacket of both cables and you can help to further secure the installation. Repeat this process for all wire connections you may need for your electrical wiring project, making sure that only wires within the recommended gauge range of the tap splice connector are used.Īfter the secured spliced cables are connected, you should tie the cables together with a plastic zip tie or use electrical tape to prevent the splice connections from being pulled apart. You should then tug on the wires to make sure a tight connection is made and the wires are securely attached to the connector. The pressure from the pliers at the splice connection will cut through the two wires and clamp together to create a secure splice connection. This pressure will squeeze the wires through a gap at the center as it penetrates the connector. Squeezing the pliers forces the metal insert into the connector. While holding the wires and tap splicers in position, you can carefully close the cover and clamp it together, slowly and carefully, with a pair of pliers. You’ll then need to close the tap splice cover carefully so that each wire inserts touches each wire. To correctly make a tap splice you’ll need to place each of the wires into a separate chamber, parallel to the length of the connector. How a Tap Splice Connector Secures Electrical ConnectionsĪ tap splice has two chambers, one on each end that is designed to securely hold two wires within the connector. To make it easy to find the right tap splicer you need, Electrical Basics provides a variety of sizes that are CSA listed for safety, with a high temperature rating up to 220 F. It is an easy and effective way of splicing wires that are commonly used in many electrical applications. Tap splicing is a reliable way of connecting two wires of the same wire gauge. The connection is completed when the tap casing is closed and crimped tightly. The plastic casing folds over and securely holds the wires, without stripping the insulation jacket, to make a tight and clean connection between the wires. When the metal portion of the tap splice is pressed down, it cuts into both wires and establishes a connection between the two wires. Tap slice connectors are designed to feed an existing wire and a new clean cut end of another wire into it. Tap splices are an inexpensive and safe way to connect an existing wire to a new wire without soldering them together. Tap splice connectors are available in various AWG wire sizes, wire combinations and colors to match AWG wire sizes. Place both ends into the twist-on connector. A very common example for the use for these tap splice connectors is for automotive trailer wiring applications when a quick and secure connection is needed. Using a Twist-On Connector Hold both pieces of wire even with each other. Tap Splicers are also referred to as Quick Splicers and are designed for use with electrical wires, some telephone wiring and other electrical device wires.

Nylon Pigtail Connectors Closed End Connectors.

Standard & High Temp Screw-On Wire Connectors.

Wire Bundling, Securing & Protection - Cable, Wire.

Color Cable Ties & Fluorescent Cable Ties.

Some cover plates have a matte surface that allows them to be painted. This technique grounds the electrical box and improves the safety of the circuit.Īfter completing the connections and finishing the wall or ceiling surface around the box, attach the cover plate securely.

#Electrical wire splice free

The free end of the pigtail is then connected to a threaded screw opening on the metal box, using a green grounding screw. For metal electrical boxes, run a third grounding pigtail (bare copper or green insulated) to the two bare copper circuit grounding wires, using a wire connector. The bare copper circuit grounding wires should also be joined together in the box, using an approved connector. With these connectors, you simply push the bare end of the wire into a grip-fit socket on the connector. Some electricians like to wrap a loop or two of electrician's tape around the base of the wire nut and wires to help reinforce the wire connection.Īnother type of approved wire connector is the push-fit connector.

There should be no bare wire exposed at the bottom of the wire nut. However you do it, the wires should be connected securely enough that they don't come free from the wire nut when you tug on them. However, some wire nut manufacturers instruct to simply hold the two parallel wires together, then twist the wire nut over the bare ends of the wires in a clockwise direction. With standard wire nuts, some electricians prefer to twist the wires together first with pliers, then screw the wire nuts over the ends of the wires. Using approved wire connectors, join together the conducting wires with similar insulation colors. The Spruce Home Improvement Review Board.